SECO-LARM E-942FC-1K3SQ Installationshandbuch PDF herunterladen

Magnetic Gate Lock Bracket Installation Manual

SECO-LARM U.S.A., Inc.

Installation Manual

E-942FC-1K3SQ

E-942FC-600SQ

Electromagnetic Lock with

Weldable Brackets for Gates

NOTICE: The information and specifications printed in this manual are current at the time of publication. However,

the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the

right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

or in part, without the written permission of SECO-LARM.

REGULAR MAINTENANCE

• Clean the contact surfaces of the electromagnet or armature plate with a soft cloth and non-abrasive, non-corrosive cleaner.

• Apply a light coat of a silicon lubricant to both contact surfaces and wipe away the excess to prevent rust.

• Check that the armature plate is securely attached to the bracket, yet can pivot slightly around the armature screw.

• Check that the electromagnet is securely attached to the bracket.

TROUBLESHOOTING

Possible cause:

No power

Poor contact between

electromagnet and

armature plate

Incorrect voltage setting

A secondary diode was

installed across the

electromagnet

Solutions:

• Check to make sure the wires are secure

• Check that the power supply is

connected and operating

• Make sure the unit is wired correctly

• Make sure the electromagnet and

armature plate are properly aligned

• Make sure the contact surfaces of the

electromagnet and armature plate are

clean and free from rust

• Check the power leads with a meter, and

make sure the correct voltage is present

• The electromagnet is fitted with a metal

oxide varistor to prevent interference, so

do not install a secondary diode

Problem:

Gate does not lock

Gate locks, but can be

easily forced open

Delay in gate releasing

• For most types of outdoor sliding and swinging electric gates.

• Includes a magnetic lock with brackets for armature and magnet.

• Brackets can be welded or bolted directly to gate.

• Holding force: E-942FC-1K3SQ – 1,300 pounds (591kg).

E-942FC-600SQ – 600 pounds (272kg).

• Brackets are zinc-plated for corrosion resistance.

• Brackets have black finish to match most gates.

• Water- and vandal-resistant attractive stainless-steel finish.

• Maintenance-free, factory-sealed design.

• Fail-safe operation (unlocks door if power is removed).

• Mounted vertically.

• Four knockouts on the junction box.

• Adapter and mounting hardware included.

• Voltage

—

12VDC or 24VDC. Prewired for 12VDC operation.

• Current draw

—

500mA @ 12VDC (250mA @ 24VDC).

MOUNTING THE ELECTROMAGNETIC LOCK

A. Determine type of gate:

1. Single-swing gate — Gate swings on one end, and comes to rest on a fixed gate post when closed. In this

case, a

typical installation has the electromagnet fixed to the gate post, and the armature connected to the free end

of the gate.

2. Double-swing gate — Two gates swing in the same direction when activated. The electromagnet is fixed to

the free end of one gate, and the armature is fixed to the free end of the other.

3. Sliding gate — The gate slides instead of swings away from a fixed gate post. A typical installation has the

electromagnet fixed to the gate post, and armature connected to the free end of the gate.

B. Mount the electromagnet — In most cases, the position of the electromagnet will determine the location of the

armature plate. Make sure there is space to run the cable.

1. Tack weld bracket into place. (Tack weld only.)

2. Dismount the electromagnetic lock from the bracket. Warning: Failure to remove electromagnetic lock will

result in severe damage to lock. Weld 3 or 4 beads about 1” apart. Make sure not to weld the junction box.

(See diagram for “No Weld” areas.)

3. Remount the electromagnetic lock.

SECO-LARM

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

Website: www.seco-larm.com

E-mail: sales

seco-larm.com

UL CERTIFICATION

Electromagnetic lock only (Model E-942FC-1300/E-942FC-600) conforms to UL/10B

“Fire Tests of Door Assemblies”

and UL/10C “Positive Pressure Fire Tests of Door Assemblies” for swinging door assemblies.

It is also classified in accordance with the Uniform Building Code standard 7-2.

E-942FC-1K3SQ Shown

LIFETIME LIMITED WARRANTY: This SECO-LARM product is warranted against defects in

material and workmanship while used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the

repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. Under no

circumstances will SECO-LARM be responsible for any costs or charges for removal, installation, or reinstallation.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,

or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such

equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at

SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or

property damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products sold and installed in

the United States and Canada. For all other countries the warranty is 1 (one) year.

ECOS

SECOSECO

SECO

L R

L RLAR

LAR

Page 1

(Magnetic lock only)

Page 4

PITSW1

FILE: DT/DTP/MiE-942FC-xxxSb.pmd

ORDER PART# 764-024%_077

1 2

Inhaltsverzeichnis

Seite 1 - Installation Manual

Magnetic Gate Lock Bracket Installation ManualSECO-LARM U.S.A., Inc. Installation ManualE-942FC-1K3SQE-942FC-600SQElectromagnetic Lock withWel

Seite 2 - Prewired 12VDC

Magnetic Gate Lock Bracket Installation ManualSECO-LARM U.S.A., Inc.Magnetic Gate Lock Bracket Installation ManualNote: AC pigtail connector is includ

Kommentare zu diesen Handbüchern

Keine Kommentare

SECO-LARM E-942FC-1K3SQ Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Elektromagnetische Schlösser SECO-LARM E-942FC-1K3SQ herunter. SECO-LARM E-942FC-1K3SQ Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern